Call Today

 

Each person has got their own perception involving How to Install a Bathtub.

Mounting a tub isn't specifically brain surgery, but it does call for solid plumbing, woodworking, and occasionally, tiling skills. Replacing an old bath tub with a new one is additionally a moderately tough project. If the old tub is conveniently available, the job can relocate rapidly; if you need to open up a wall to eliminate the old bathtub and also place the new bath tub, the task is a lot harder. In either case, the task is within a residence handyman's skills, although you will certainly need a helper to leave the old bathtub and also embeded in the brand-new one. Make sure you have qualified yourself for the job as well as are comfortable attempting it. Instead of employing a service provider to take control of a halfway-completed job, it is much better to think about utilizing one before you begin. Opportunities are you might require an expert plumber to make tube connections.
This write-up will certainly assist you install a brand-new tub in your restroom if you have currently gotten a new bathtub as well as do not need to change the setup of your previous water system pipes.
Your devices and product checklist must comprise the following:

 

• New Tub


• Hammer


• Pipe Wrenches


• Prybar


• Shatterproof glass


• Degree


• Pliers


• Adjustable Wrench


• Putty Blade


• Screwdriver


• Cold Chisel


• Measuring tape


• Pipeline Caps


 

Removing Old Taps

If you need to change old taps with new ones as a part of your setup, after that the first thing you should do is detach the water. After doing so, turn on the taps to drain any type of water continuing to be in the system. The process of removing the existing taps can be fairly troublesome because of the limited accessibility that is frequently the situation.
Make use of a basin wrench (crowsfoot spanner) or a tap tool to undo the nut that connects the supply pipes to the taps. Have a cloth ready for the remaining water that will originate from the pipelines. As soon as the supply pipelines have been eliminated, utilize the same tool to loosen up the nut that holds the faucets onto the bath/basin. You will require to quit the single taps from transforming during this process. As soon as the taps have actually been gotten rid of, the holes in the bath/basin will have to be cleansed of any type of old sealing substance.
Before going on to fit the new faucets, contrast the pipeline connections on the old taps to the brand-new taps. If the old taps are longer than the brand-new taps, then a shank adapter is needed for the new faucets to fit.

 

 

Suitable New Taps

If the tails of the new faucets are plastic, then you will certainly need a plastic connector to stop damage to the thread. One end of the adapter fits on the plastic tail of the faucet and the various other end offers a link to the current supply pipelines.
If you require to fit a monobloc, then you will certainly call for reducing couplers, which connects the 10mm pipe of the monobloc to the common 15mm supply pipeline.
Next off, position the tap in the placing opening in the bath/basin making certain that the washing machines are in area in between the tap and the sink. Safeguard the faucet in place with the producer provided backnut. As soon as the tap is securely in position, the supply pipes can be connected to the tails of the faucets. The faucets can either be linked by using corrugated copper piping or with normal faucet adapters. The previous kind must be linked to the faucet finishes first, tightening only by hand. The supply pipelines can later on be attached to the various other end. Tighten both ends with a spanner after both ends have been connected.

 

 

Mounting the Tub

Utilizing the two wood boards under its feet, place the tub in the required setting. The wood boards are valuable in equally spreading out the weight of the tub over the area of the boards as opposed to focusing all the weight onto 4 little factors.
The following goal is to make sure that the bathtub is leveled all round. This can be attained by inspecting the spirit level and adjusting the feet on the bathtub till the spirit level reviews level.
To install faucets, fit the bottom of the outermost versatile faucet port to the appropriate supply pipeline by making a compression join; after that do the same for the other tap.
Turn on the water and also examine all joints and also brand-new pipework for leaks and also tighten them if essential. Fill the bathtub as well as additionally inspect the overflow outlet and also the normal electrical outlet for leakages.
Ultimately, repair the bathroom paneling as described in the producer's instruction manual. Tiling and securing around the tub should wait up until the bathtub has actually been used at the very least once as this will resolve it into its final placement.

 

 

Getting ready for the Installment

Firstly, the supporting structure provided with the bath ought to be fitted (if called for) according to the manufacturer's instructions. Next, fit the faucets or mixer to the bath tub. When suitable the faucet block, it is essential to ensure that if the faucet includes a plastic washing machine, it is fitted in between the bathroom as well as the faucets. On a plastic bath, it is likewise practical to fit a supporting plate under the taps unit to prevent strain on the bath tub.
Fit the adaptable faucet ports to the bottom of the two taps making use of 2 nuts and also olives (often supplied with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet hole, and afterwards pass the electrical outlet with the hole in the bathroom. Utilize the nut supplied by the supplier to fit the plug-hole. Take a look at the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next, fit completion of the flexible overflow pipe to the overflow outlet. Afterwards, screw the pipeline to the overflow face which must be fitted inside the bathroom. Make sure you utilize every one of the supplied washing machines.
Connect the catch to the bottom of the waste outlet on the bath tub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, as well as screw on the trap to the electrical outlet. Connect the bottom of the overflow tube in a comparable manner.The bath should now prepare to be fitted in its last position.

 

 

Tiling Around the Bath tub

In the area where the bath fulfills the tile, it is needed to seal the joins with a silicone rubber caulking. This is important as the installation can relocate enough to fracture a rigid seal, creating the water to penetrate the wall between the bathroom and also the tiling, causing problems with dampness as well as possible leakages to the ceiling below.
You can pick from a selection of coloured sealants to assimilate your fixtures and also installations. They are sold in tubes and also cartridges, and also can sealing gaps up to a width of 3mm (1/8 inch). If you have a larger gap to fill, you can fill it with spins of drenched paper or soft rope. Bear in mind to constantly fill up the tub with water before sealing, to enable the movement experienced when the tub remains in use. The sealant can split rather very early if you do not consider this movement before securing.
Conversely, ceramic coving or quadrant ceramic tiles can be utilized to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use as well as cut to dimension, are likewise easily readily available on the market. It is advisable to fit the floor tiles utilizing waterproof or water resistant adhesive as well as cement.

 

A Step-by-Step Guide to Installing a Bathtub

 

Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.

But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.

This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.

 

Remove the Existing Bathtub

 

To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.

The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.

 

Choose the Right Bathtub

 

The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.

 

Install the Plumbing and Ledger Board

 

You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.

Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.

 

Install the Bathtub

 

When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.

Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.

If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.

 

Hook up the Plumbing

 

Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.

 

Install the Bathtub Surround

 

A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.

Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.

If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.

If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.

https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/

 

Do you enjoy more info about Tools You Need to Install a New Bathtub ? Write feedback down below. We would be interested to know your ideas about this blog entry. Hoping to see you back again before long. I beg you take a moment to promote this content if you appreciated it. Thank you so much for going through it.

Act fast, Call us!